Matek AP_Periph CAN-L4-BM Digital Power Monitor

COMING SOON
Matek AP_Periph CAN-L4-BM Digital Power Monitor at WREKD Co.
Matek AP_Periph CAN-L4-BM Digital Power Monitor at WREKD Co.
Matek AP_Periph CAN-L4-BM Digital Power Monitor at WREKD Co.
SAVE 5% OFF YOUR FIRST ORDER
Use discount code FIRSTLEGENDS at checkout.

EXCLUSIVE DISCOUNTS AVAILABLE
Military, First Responders & Students
Learn More

Matek AP_Periph CAN-L4-BM Digital Power Monitor

COMING SOON

Regular price $29.99
/
Ask us a question
NOTE: This item is on backorder, which means it will be delivered as soon as we receive our next shipment from our supplier. This typically ranges from 1 to 3 weeks.

Earn 116 CaveCoin by purchasing this item.

or Sign Up to start earning on your next order.

About this item

The Matek AP_Periph CAN-L4-BM CAN Digital Power Monitor offers ultra-precise monitoring for your drone needs. It features a low-power resistant path of 200μΩ, providing high efficiency in power consumption. No calibration is required and DroneCAN protocol offers convenient current & bus voltage readouts. Enjoy precision monitoring and convenience with the AP_Periph CAN CAN-L4-BM.

Check out all our GPS modules, and our full line of Matek products!

Specifications

  • MCU: STM32L431xC, 256KB Flash
  • INA239 85-V, 16-Bit, High-Precision Power monitor IC With SPI Interface
  • Battery Voltage sense input: 0~85V
  • Current Sense Range: 0~204.8A
  • Load current on current sensing resistor: 150A(Continuous), 204.8A(Burst)
  • Voltage accuracy: ± 0.1%
  • Current accuracy: ± 2%
  • Interface: CAN, DroneCAN Protocol, U-ART2, spare, DFU, -ST debug, SWCLK & SWDIO
  • LED: Blue, (Fast blinking, Booting), Blue, (Slow blinking, working) Red, (3.3V indicator)
  • Power supply for CAN-L4-BM board: 4.5~5.5V @5V pad/pin
  • Power consumption: 10mA
  • Operating Temperatures: -40~85 °C
    Board Size: 30mm x 22mm x 3mm.
  • Weight: 4g
  • 3D file: CAN-L4-BM_STEP.zip
  • Firmware: ArduPilot AP_Periph  MatekL431-BattMon
  •  Update: via DroneCAN GUI Tool
  • Parameters: CAN_P1_DRIVER = 1 if attached to CAN bus1 port or CAN_P2_DRIVER = 1 if attached to CAN bus2 port, BATTx_MONITOR = 8 (DroneCAN-BatteryInfo)

Tips

  • The big pad on the bottom side is a dead pad. No any circuit network on it.
  • Solder the positive wires as close as possible to both sides of the current sensing resistor.
  • 2 ears for mounting can be cut off if you don’t need it.
  • If the CAN wires are too long, bridge the “120R” jumper.

Includes

  • 1x Matek AP_Periph CAN-L4-BM Digital Power Monitor
  • 1x JST-GH-4P to JST-GH-4P 20cm silicon wire

Wiring Diagram 

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
Recently viewed